P0341 Camshaft Position Sensor (cam sensor / timing chain)

Rickw wrote:

I'll assume with infinite resistance between the ICM and PCM the car wouldn't run at all.?

No its just the designated Cam Sensor wire which is one of many wires going from the ICM to PCM. I tested one of the other wires going to the PCM and found zero resistance in order to confirm the testing procedure.

_________________

1996 Riviera, 1.9s, 3" DP, FWI, 180, AL104s, 3.6", DHP PowrTuning...
Soon: SSACs, Stage 1 TB, and a 3.4

I'll repost what I found:PO341 code, 1998 Riviera
I found a broken wire in connector c101, pin a7, black 18 gauge wire to the ignition module. The wire was broken inside the insulation so it looked like it was good from the outside. C101 is the big 72 wire connector near the trans dip stick and A7 is the black wire on the bottom left side of the connector. It's a tight squeeze but you have to cut the wire before and after the connector to jump around it. Test the connection first with a meter between the connector then after confirming the open, gently pull on the wire with a needle nose from the front of the connector, and look to see that the insulation stretches indicating that wire inside is broken from the stress of the weight of the harness.

tech408 wrote:

I'll repost what I found:PO341 code, 1998 Riviera
I found a broken wire in connector c101, pin a7, black 18 gauge wire to the ignition module. The wire was broken inside the insulation so it looked like it was good from the outside. C101 is the big 72 wire connector near the trans dip stick and A7 is the black wire on the bottom left side of the connector. It's a tight squeeze but you have to cut the wire before and after the connector to jump around it. Test the connection first with a meter between the connector then after confirming the open, gently pull on the wire with a needle nose from the front of the connector, and look to see that the insulation stretches indicating that wire inside is broken from the stress of the weight of the harness.

Excellent post - only one thing to add.

Because of where the wire is broken, another option is to repair the connection. Use a jeweler's screwdriver to back the terminal out of the connector. Using a small vise or a pair of vise grips to hold the terminal, spread the wire crimp open (or simply use another pair of needletip pliers to yank out the butt of the wire). Then take the pin back out to the car. If there is enough wire in the harness you can simply strip a bit and solder the terminal back on, then reinsert it into the connector using that jewelers screwdriver if needed. If there is not enough wire in the harness, then splice, solder and insulate a short length on sufficient to let you reattach (solder) the terminal back on and reinsert it into the harness. If you do the repair this way you MUST be careful not to distort or fatigue the terminal because if you do it won't re-insert, will break on reinsertion, or some other failure.

Don't get me wrong - I am NOT saying Tech408's approach is bad, because it is a standard and avoids the problems that can ensue if you attempt to repair the connector without the Kent-Moore equipment. Another advantage is that Tech408's approach makes it real easy to find later where a harness has been spliced, and yet another advantage is that terminals to be repaired properly at a convenient time/place in the future are real easy to find. It's a good field fix. However I think you all might benefit from being aware of this alternative in cases where it's an advantage to repair in such a way that the connector can be normally detached, unless you also plan to put a spade or bullet connector in your splice.

In the FSM the approach that is taught is to use a repair kit to replace the bad terminal - pin or socket - in the connector, which if you have the Kent-Moore kit is fairly easy. Problem is, the kit is a cathedral unto itself -- take a look

http://www.acdelcotechconnect.com/pdf/imtn_V11I404.pdf

https://gmspecialservicetools.spx.com/Documents/Promotions/GM08-195.PDF (with prices)

These silly kits cost a bundle - great for a busy busy repair shop but just not something in a journeyman's reach. Give you a hint - the complete kit lists for about $6,100.-

Again - excellent post.

Albertj

_________________
1998 with all fac. opts. (exc. CD changer and subwoofer); 209,000 miles. Mods: KYB front struts, extra noise barriers, fire extinguisher, Magnecor 8mm plug wires, 4-note horn, custom-made stainless exhaust.

Avatar is missing.

Ok just want to make sure that I'm testing the right wire and getting a correct readout from my ohm meter. I'm testing the black wire that is designated Camshaft Position Sensor input at pin 5 (shown in the chart below) at the PCM, and also testing the believed corresponding black wire at the ICM where the large connector is (shown in picture below) for circuit resistance. When it was tested in this fashion it returned an infinite resistance. Just need to know if this reading is true because the wire is bad or it read that value because its the wrong wire.

_________________

1996 Riviera, 1.9s, 3" DP, FWI, 180, AL104s, 3.6", DHP PowrTuning...
Soon: SSACs, Stage 1 TB, and a 3.4

check for continuity between the point you highlighted and the large connector to the left of the brake booster on the firewall. the circuit starts at the CPS, then into the ignition module, out of the ignition module, into the connector on the firewall, out of the connector and finally into the ECM. Read the details from my original post. It describes the exact locations. Good Luck

tech408 wrote:

check for continuity between the point you highlighted and the large connector to the left of the brake booster on the firewall. the circuit starts at the CPS, then into the ignition module, out of the ignition module, into the connector on the firewall, out of the connector and finally into the ECM. Read the details from my original post. It describes the exact locations. Good Luck

Is my method inconclusive? It seems that the test you are calling for it very similar. I understand that your test will allow me to pinpoint the area of trouble but the planned solution was to splice in a new black wire near the ICM and route it along the passenger-side fender through the firewall to the PCM as turtleman did with his. I am in no way bashing your approach, just wondering how it differs smile

_________________

1996 Riviera, 1.9s, 3" DP, FWI, 180, AL104s, 3.6", DHP PowrTuning...
Soon: SSACs, Stage 1 TB, and a 3.4

L67 wrote:

tech408 wrote:

check for continuity between the point you highlighted and the large connector to the left of the brake booster on the firewall. the circuit starts at the CPS, then into the ignition module, out of the ignition module, into the connector on the firewall, out of the connector and finally into the ECM. Read the details from my original post. It describes the exact locations. Good Luck

Is my method inconclusive? It seems that the test you are calling for it very similar. I understand that your test will allow me to pinpoint the area of trouble but the planned solution was to splice in a new black wire near the ICM and route it along the passenger-side fender through the firewall to the PCM as turtleman did with his. I am in no way bashing your approach, just wondering how it differs smile

I never looked at the pinout for the engine harness as it plugs into the firewall but you could check it from the ICM to there instead of the ICM all the way to the PCM inside. More than likely, the failed wire would be under the hood, rather than inside the car under the dash, but nothing's impossible.

To answer your original question, Matt, unfortunately the same reading of infinite resistance means it could be a broken connection in the wire or wrong wire just the same. It is important to be sure that you are looking at the right wire. It doesn't hurt to test other same color wires to be sure as I've found that my factory service manual actually said the wrong PCM connector.

If you have the pinout for the firewall connector, I would go head and check it to the ICM connector, like tech408 said. Don't forget to check between the actual cam sensor and ICM also! The trend for failure seems to be between the PCM and ICM but it's still entirely possible the problems right there.

_________________
1997 turtle

turtleman wrote:

L67 wrote:

tech408 wrote:

check for continuity between the point you highlighted and the large connector to the left of the brake booster on the firewall. the circuit starts at the CPS, then into the ignition module, out of the ignition module, into the connector on the firewall, out of the connector and finally into the ECM. Read the details from my original post. It describes the exact locations. Good Luck

Is my method inconclusive? It seems that the test you are calling for it very similar. I understand that your test will allow me to pinpoint the area of trouble but the planned solution was to splice in a new black wire near the ICM and route it along the passenger-side fender through the firewall to the PCM as turtleman did with his. I am in no way bashing your approach, just wondering how it differs smile

I never looked at the pinout for the engine harness as it plugs into the firewall but you could check it from the ICM to there instead of the ICM all the way to the PCM inside. More than likely, the failed wire would be under the hood, rather than inside the car under the dash, but nothing's impossible.

To answer your original question, Matt, unfortunately the same reading of infinite resistance means it could be a broken connection in the wire or wrong wire just the same. It is important to be sure that you are looking at the right wire. It doesn't hurt to test other same color wires to be sure as I've found that my factory service manual actually said the wrong PCM connector.

If you have the pinout for the firewall connector, I would go head and check it to the ICM connector, like tech408 said. Don't forget to check between the actual cam sensor and ICM also! The trend for failure seems to be between the PCM and ICM but it's still entirely possible the problems right there.

I did check another wire using the PCM pin chart I have and it returned zero resistance, so i believe that the pin # given to me for the black wire is correct. However I will still check the firewall harness to make sure that it is correct.

_________________

1996 Riviera, 1.9s, 3" DP, FWI, 180, AL104s, 3.6", DHP PowrTuning...
Soon: SSACs, Stage 1 TB, and a 3.4

Here's some more stuff (including fuller images of somethings i posted) that someone may find of use.

_________________

1996 Riviera, 1.9s, 3" DP, FWI, 180, AL104s, 3.6", DHP PowrTuning...
Soon: SSACs, Stage 1 TB, and a 3.4

hopefully the problem will be fixed soon I'm the latest person to have a crack at fixing it (I'm also L67's older brother for any new members here) it's been helping me get my performance objectives done in my electrical class. (hopefully i do not end up with the other poor souls who couldn't fix it). The game plan is exactly what L67 said which involves the said wire splice. I'm just hoping the Car alarm does not throw another revolt like last week where it was set off by absolutely everything.

_________________

Well GMfan1111 tested my car is his auto electrical class today and found some continuity issues between the ICM and previously mentioned firewall connector in the black wire. So it seems that that wire problem. He ran out of time in his class so the wire splicing will have to wait until next week.

_________________

1996 Riviera, 1.9s, 3" DP, FWI, 180, AL104s, 3.6", DHP PowrTuning...
Soon: SSACs, Stage 1 TB, and a 3.4

Well my brother and dad were working on my car back home and found this:

The arrow points to the end of the black CPS wire that is cut from the circled plug in the big connector behind the trans dipstick that was mentioned a few posts up. It must've been weak or frayed when i was doing the rocker install, and all of the movement of parts to access the back VC tore it apart.

_________________

1996 Riviera, 1.9s, 3" DP, FWI, 180, AL104s, 3.6", DHP PowrTuning...
Soon: SSACs, Stage 1 TB, and a 3.4

Good find. Hopefully all your issues will be taken care of with this repair.

_________________
98 Riv, 102K Miles, EBC, LS1 Ft.Calipers, STB, Addco Rr Sway Bar, 180* stat., SSAC Headers, HF Cat, 1.9's,
105# springs, MPS 3.4, DHP tuned by the Deekster.

_________________
'98 Buick Riviera; Gen V 3.25 pulley, N*, VS Cam, 180 stat, Custom PCM (Powrtuner), headers & HF cat , 42.5 lb inj.

Grant-built/PRJ/Thrasher trans 3.29 gears, 7/8 chain, zzp hardened IS

Good Work! clap

And thanks for taking the time to post the pics.

Bert tavis

_________________
99 Riviera(on the left)
"Cruising Missile"
Midnight Blue Pearl
90,000 miles
GuttedAirBox

70GS455(on the right)
Diplomat Blue
"Howitzer with windshield wipers"